How do I reset my Juniper SSG 140?

How do I reset my Juniper SSG 140?

The reset pinhole is a button that resets the device to its original default settings. To use this button, insert a stiff wire (such as a straightened paper clip) into the pinhole. See “Resetting the Device to Factory Defaults” on page 32 for more information.

How do you reset a Juniper switch?

Reverting to the Default Factory Configuration by Using the Menu Button

1. Press the Menu button until you see MAINTENANCE MENU on the panel.
2. Press the Enter button.
3. Press Menu until you see FACTORY DEFAULT.
4. Press Enter. The display says RESTORE DEFAULT?
5. Press Enter.

How do I reset my SSG 20 Juniper?

Here is the two procedures to reset your Juniper SSG ScreenOS device….

1. Using a thin, firm wire (such as a paper clip), push the pinhole for four to six seconds, and then release.
2. Wait for one-half to two seconds.
3. Push the reset pinhole again for four to six seconds.

How do I reset Juniper SSG 5?

On the back of the SSG you will see a reset pin hole. You need to use a paperclip or similar. I use a trusty iPhone sim tool. Push in the reset button for 4 to 6 seconds and then release.

How do I clear the configuration on a Juniper router?

From the CLI, enter unset all; press ENTER. When prompted for Erase all system config, are you sure y/[n]; press y. Enter reset; press ENTER….Symptoms:

1. Configuration.
2. Unset all.
3. Erase configuration.

How do I wipe my Juniper router?

Restore Juniper SRX210 to factory default configuration

1. Power on the Juniper SRX210 by plugging it to the power adapter.
2. Using a pin or paperclip, press and hold the RESET CONFIG button for 15 seconds.
3. Wait about 2 minutes while the Juniper SRX210 restores to the factory default settings.

What is Juniper default password?

Change or modify – The default password (abc123) is used during initial configuration, after installation.

How do I reset my juniper EX2200 to factory settings?

8. RE: reset factory default EX2200

1. Start a root shell by logging in as root and then either omit the cli command or from operations mode, type start shell.
2. Change into the /config directory by cd /config.
3. Delete all files from there by rm *
4. Reboot your device.

How do I reset my Juniper NetScreen 5GT?

You can reset the NetScreen-5GT and restore the factory default settings by pressing the reset pinhole. To perform this operation, you need to either view the status LEDs on the front panel or have a Console session as described in “Using a Console Connection” on page 8. 1. Locate the reset pinhole on the rear panel.

How do I access Juniper ssg5?

Launch a browser. In the URL address field, enter http://192.168.1.1. The Rapid Deployment Wizard window appears. (The default login admin name and password is netscreen.)

How do I reset my Juniper router?

To restart the switch from the front panel:

1. From the LCD front panel menu push the Menu button.
2. When the MAIN MENU (Maintenance menu) appears, press the Enter button.
3. Select the SYSTEM REBOOT option and press the Enter button.
4. To exit the menu without rebooting the switch, press the Menu button again.

How do I reset my juniper ssg5 password?

How To Recover Password Juniper SSG 550 Using Serial Number

1. Connect to the device with a console connection.
2. Log into the firewall using the device’s serial number as both the username and password.
3. A warning message will display, requesting confirmation to continue with the process.
4. A reconfirmation message displays.

How to reset juniper ssg-140 admin password-factory default?

The following instructions will reset the SSG-140 to factory default. Resetting ScreenOS to factory default will wipe out the whole configuration of the device and you need to reconfigure or restore configuration from backup. METHOD 1: 1- Connect to it through Console/Serial. 2- Login with the serial number of the SSG as the username and password.

How to reset juniper firewall to factory default?

If you don’t have a backup config file, you will need to manually re-configure the firewall. METHOD 2: If you don’t have a console cable you can hard reset the Juniper firewall using the following instructions – This will also reset it to factory default: Push and hold the pinhole on the Juniper.

What is the IP address for Juniper SSG 5?

Once the settings have reset to default you can access your Juniper SSG 5 unit using the following default IP address, username and password: IP Address: 192.168.1.1

What do you need to know about SSG 140?

The Juniper Networks Secure Services Gateway (SSG) 140 devices is an integrated router and firewall platform. It provides Internet Protocol Security (IPSec) virtual private network (VPN) and firewall services for small- and medium-sized companies and enterprise branch and remote offices. POWER HA PIM1 PIM3